CDL Doubles/Triples Endorsement Practice Test

50 questions on hooking up a second and third trailer with a converter dolly, checking air to the rear, and why the last trailer whips in a quick lane change.

50 questionsEvery answer explained

Practice Mode

50questions

Work through all 50 questions. Stop anytime — your progress is saved.

Exam Simulation

20questions
25min
16/20Passing

Flashcards · try 3

1 / 3

Practice by Category

Work through a whole topic — every question in it.

Sample questions with answers

9 more from the 50-question bank — tap to see the answer

1

Under federal rules, what does attaching a converter dolly to a semitrailer do?

  • Lets it tow without air lines
  • Converts it into a straight truck
  • Adds a drive axle to the tractor
  • Answer: Converts it into a full trailer

A converter dolly has axles, a fifth wheel, and a drawbar; attaching it converts a semitrailer to a full trailer.

Source: 49 CFR §393.5

2

How do you release the brakes on a converter dolly that has no spring brakes?

  • Pull the pintle hook release
  • Push in the trailer air supply knob
  • Answer: Open the dolly air tank petcock
  • Close the dolly air tank petcock

Dolly brakes are released by opening the air tank petcock, or with the parking brake control if the dolly has spring brakes.

Source: CDL Manual §7.2.1

3

When you wheel the converter dolly into place in front of the rear trailer, how should it line up?

  • Answer: In line with the kingpin
  • Angled toward the first trailer
  • Offset toward the driver's side
  • Centered under the landing gear

Position the dolly in front of the second trailer, lined up with its kingpin.

Source: CDL Manual §7.2.1

Show 6 more
4

After hooking the converter dolly to the front trailer, what must you do?

  • Open the dolly air tank petcock and lower the converter gear support
  • Answer: Lock the pintle hook and raise the converter gear support
  • Connect the light cord to the rear trailer
  • Release the dolly fifth wheel latch

Once the dolly is hooked to the first trailer, lock the pintle hook and secure the converter gear support in the raised position.

Source: CDL Manual §7.2.1

5

Before backing the dolly under the rear trailer, how high should the trailer's front be?

  • Resting on the ground
  • Level with the tops of the dolly tires
  • Answer: Slightly lower than the center of the dolly's fifth wheel
  • Slightly higher than the fifth wheel, so the dolly slides under it

The trailer should sit a little low so it is raised slightly when the dolly is pushed under it.

Source: CDL Manual §7.2.1

6

Right after backing the dolly under the rear trailer, what should you do with the trailer's landing gear?

  • Leave it resting firmly on the ground until the trip
  • Answer: Raise it slightly off the ground
  • Raise it all the way up
  • Take out the crank handle

Lifting the landing gear slightly prevents damage if the trailer moves; it is raised completely later, after the lines are connected.

Source: CDL Manual §7.2.1

7

How do you test the coupling between the dolly and the second semitrailer?

  • Answer: Pull against the pin of the second trailer
  • Back the dolly harder under it
  • Rock the trailer by hand
  • Open the emergency line valve and listen for air

Test the connection by pulling against the second semitrailer's kingpin, then check it visually.

Source: CDL Manual §7.2.1

8

After connecting the dolly to the rear trailer, what should the dolly air tank petcock be?

  • Half open
  • Removed
  • Answer: Closed
  • Open

During coupling you close the converter dolly air tank petcock; on inspection the dolly air tank drain valve should be closed.

Source: CDL Manual §7.3.1

9

You open the emergency line valve at the rear of the last trailer and hear no air. What should you check first?

  • That the light cord is plugged in
  • Answer: That the trailer and dolly shut-off valves are open
  • That the dolly air tank petcock is fully open and draining
  • That the trailer tires are inflated

If no air escapes, check that the shut-off valves on the trailers and dollies are open; air must reach the back for all brakes to work.

Source: CDL Manual §7.4.1

About the CDL Doubles and Triples test

How many questions are on the CDL Doubles and Triples test?

State agencies list it at 20 questions with a pass at 16. Some states, such as Michigan, describe the endorsement as double trailers only, so check whether yours allows triples at all.

Who has to take it?

You need it for the T endorsement to pull double or triple trailers. It covers coupling and uncoupling the second and third trailers and converter dollies, inspecting doubles and triples, the air brake check for them, and the crack-the-whip effect.

Is there a time limit?

Federal rules don't set one and states differ, many give no fixed limit. Our mock uses 25 minutes so you practise working at a steady pace.

Are these the real test questions?

No. States draw from question pools that the FMCSA approves and does not publish. Every question here was written by GoExam from the facts in the commercial driver's manual and the federal regulations in 49 CFR, and shows its source. A second reviewer answered each one without seeing our key; questions where the answers differed were dropped. Where the manual and the current regulation disagree, we don't ask about it.

Do I need a learner's permit first?

Yes. You pass the knowledge tests to get a Commercial Learner's Permit (CLP), and can take the skills test no sooner than 14 days after the CLP is first issued (49 CFR 383.25). Since February 7, 2022 you must also finish entry-level driver training from a registered provider before your first Class A or B skills test, your first P or S skills test, or your first H knowledge test (49 CFR 383.71).

Questions written by GoExam from the commercial driver's license manual and the Federal Motor Carrier Safety Regulations (49 CFR). They are not official test questions. 49 CFR Part 383 (eCFR)

Other licence classes

Other exams in United States